Displays and Other Outputs

In this chapter, you will learn how to control physical hardware via BeagleBone Black’s general-purpose input/output (GPIO) pins. The Bone has 65 GPIO pins that are brought out on two 46-pin headers, called P8 and P9, as shown in The P8 and P9 GPIO headers.

Note

All the examples in the book assume you have cloned the Cookbook repository on git.beagleboard.org. Go here Cloning the Cookbook Repository for instructions.

Fig. 427 The P8 and P9 GPIO headers

The purpose of this chapter is to give simple examples that show how to use various methods of output. Most solutions require a breadboard and some jumper wires.

All these examples assume that you know how to edit a file (Editing Code Using Visual Studio Code) and run it, either within Visual Studio Code (VSC) integrated development environment (IDE) or from the command line (Getting to the Command Shell via SSH).

Toggling an Onboard LED

Problem

You want to know how to flash the four LEDs that are next to the Ethernet port on the Bone.

Solution

Locate the four onboard LEDs shown in The four USER LEDs. They are labeled USR0 through USR3, but we’ll refer to them as the USER LEDs.

Fig. 428 The four USER LEDs

Place the code shown in Using an internal LED (internLED.py) in a file called internLED.py. You can do this using VSC to edit files (as shown in Editing Code Using Visual Studio Code) or with a more traditional editor (as shown in Editing a Text File from the GNU/Linux Command Shell).

PythonC

Listing 31 Using an internal LED (internLED.py)

#!/usr/bin/env python
# //////////////////////////////////////
# 	internLED.py
# 	Blinks A USR LED.
# 	Wiring:
# 	Setup:
# 	See:
# //////////////////////////////////////
import gpiod
import time

LED_CHIP = 'gpiochip1'
LED_LINE_OFFSET = [21]  # USR0 run: gpioinfo | grep -i -e chip -e usr

chip = gpiod.Chip(LED_CHIP)

lines = chip.get_lines(LED_LINE_OFFSET)
lines.request(consumer='internLED.py', type=gpiod.LINE_REQ_DIR_OUT)

state =  0      # Start with LED off
while True:
    lines.set_values([state])
    state = ~state      # Toggle the state
    time.sleep(0.25)

internLED.py

In the bash command window, enter the following commands:

bone$ cd ~/beaglebone-cookbook-code/03displays
bone$ ./internLED.py

The USER0 LED should now be flashing.

Toggling an External LED

Problem

You want to connect your own external LED to the Bone.

Solution

Connect an LED to one of the GPIO pins using a series resistor to limit the current. To make this recipe, you will need:

• Breadboard and jumper wires.

• 220 Ω to 470 Ω resistor.

• LED

Warning

The value of the current limiting resistor depends on the LED you are using. The Bone can drive only 4 to 6 mA, so you might need a larger resistor to keep from pulling too much current. A 330 Ω or 470 Ω resistor might be better.

Diagram for using an external LED shows how you can wire the LED to pin 14 of the P9 header (P9_14). Every circuit in this book (Wiring a Breadboard) assumes you have already wired the rightmost bus to ground (P9_1) and the next bus to the left to the 3.3 V (P9_3) pins on the header. Be sure to get the polarity right on the LED. The _short_ lead always goes to ground.

Fig. 429 Diagram for using an external LED

After you’ve wired it, start VSC (see Editing Code Using Visual Studio Code) and find the code shown in Code for using an external LED (externLED.py). Notice that it looks very similar to the internLED code, in fact it only differs in the line number (18 instead of 21). The built-in LEDs use the same GPIO interface as the GPIO pins.

PythonC

Listing 33 Code for using an external LED (externLED.py)

#!/usr/bin/env python
# //////////////////////////////////////
# 	externLED.py
# 	Blinks an external LED wired to P9_14.
# 	Wiring: P9_14 connects to the plus lead of an LED.  The negative lead of the
#		LED goes to a 220 Ohm resistor.  The other lead of the resistor goes
#		to ground
# 	Setup:
# 	See:
# //////////////////////////////////////
import gpiod
import time

LED_CHIP = 'gpiochip1'
LED_LINE_OFFSET = [18]  # P9_14 run: gpioinfo | grep -i -e chip -e P9_14

chip = gpiod.Chip(LED_CHIP)

lines = chip.get_lines(LED_LINE_OFFSET)
lines.request(consumer='internLED.py', type=gpiod.LINE_REQ_DIR_OUT)

state =  0      # Start with LED off
while True:
    lines.set_values([state])
    state = ~state      # Toggle the state
    time.sleep(0.25)

externLED.py

Save your file and run the code as before (Toggling an Onboard LED).

Toggling a High-Voltage External Device

Problem

You want to control a device that runs at 120 V.

Solution

Working with 120 V can be tricky –even dangerous– if you aren’t careful. Here’s a safe way to do it.

To make this recipe, you will need:

• PowerSwitch Tail II

Diagram for wiring PowerSwitch Tail II shows how you can wire the PowerSwitch Tail II to pin P9_14.

Fig. 430 Diagram for wiring PowerSwitch Tail II

After you’ve wired it, because this uses the same output pin as Toggling an External LED, you can run the same code (Code for using an external LED (externLED.py)).

Fading an External LED

Problem

You want to change the brightness of an LED from the Bone.

Solution

Use the Bone’s pulse width modulation (PWM) hardware to fade an LED. We’ll use the same circuit as before (Diagram for using an external LED). Find the code in Code for using an external LED (fadeLED.py) Next configure the pins. We are using P9_14 so run:

bone$ config-pin P9_14 pwm

Then run it as before.

PythonJavaScript

Listing 35 Code for using an external LED (fadeLED.py)

#!/usr/bin/env python
# ////////////////////////////////////////
# //	fadeLED.py
# //	Blinks the P9_14 pin
# //	Wiring:
# //	Setup:  config-pin P9_14 pwm
# //	See:
# ////////////////////////////////////////
import time
ms = 20;   # Fade time in ms

pwmPeriod = 1000000    # Period in ns
pwm     = '1'  # pwm to use
channel = 'a'  # channel to use
PWMPATH='/dev/bone/pwm/'+pwm+'/'+channel
step = 0.02    # Step size
min = 0.02     # dimmest value
max = 1        # brightest value
brightness = min # Current brightness

f = open(PWMPATH+'/period', 'w')
f.write(str(pwmPeriod))
f.close()

f = open(PWMPATH+'/enable', 'w')
f.write('1')
f.close()

f = open(PWMPATH+'/duty_cycle', 'w')
while True:
    f.seek(0)
    f.write(str(round(pwmPeriod*brightness)))
    brightness  += step
    if(brightness >= max or brightness <= min):
        step = -1 * step
    time.sleep(ms/1000)

# | Pin   | pwm | channel
# | P9_31 | 0   | a
# | P9_29 | 0   | b
# | P9_14 | 1   | a
# | P9_16 | 1   | b
# | P8_19 | 2   | a
# | P8_13 | 2   | b

fadeLED.py

The Bone has several outputs that can be use as pwm’s as shown in Table of PWM outputs. There are three EHRPWM’s which each has a pair of pwm channels. Each pair must have the same period.

Fig. 431 Table of PWM outputs

The pwm’s are accessed through /dev/bone/pwm

bone$ cd /dev/bone/pwm
bone$ ls
0  1  2

Here we see three pwmchips that can be used, each has two channels. Explore one.

bone$ cd 1
bone$ ls
a  b
bone$ cd a
bone$ ls
capture  duty_cycle  enable  period  polarity  power  uevent

Here is where you can set the period and duty_cycle (in ns) and enable the pwm. Attach in LED to P9_14 and if you set the period long enough you can see the LED flash.

bone$ echo 1000000000 > period
bone$ echo  500000000 > duty_cycle
bone$ echo 1 > enable

Your LED should now be flashing.

Headers to pwm channel mapping are the mapping I’ve figured out so far. I don’t know how to get to the timers.

Table 134 Headers to pwm channel mapping

Pin	pwm	channel
P9_31	0	a
P9_29	0	b
P9_14	1	a
P9_16	1	b
P8_19	2	a
P8_13	2	b

Writing to an LED Matrix

Problem

You have an I²C-based LED matrix to interface.

Solution

There are a number of nice LED matrices that allow you to control several LEDs via one interface. This solution uses an Adafruit Bicolor 8x8 LED Square Pixel Matrix w/|I2C| Backpack.

To make this recipe, you will need:

• Breadboard and jumper wires

• Two 4.7 kΩ resistors.

• I²C LED matrix

The LED matrix is a 5 V device, but you can drive it from 3.3 V. Wire, as shown in Wiring an I2C LED matrix.

Fig. 432 Wiring an I²C LED matrix

Measuring a Temperature shows how to use i2cdetect to discover the address of an I²C device.

Run the i2cdetect -y -r 2 command to discover the address of the display on I²C bus 2, as shown in Using I2C command-line tools to discover the address of the display.

Using I²C command-line tools to discover the address of the display

bone$ i2cdetect -y -r 2
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- 49 -- -- -- -- -- --
50: -- -- -- -- UU UU UU UU -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: 70 -- -- -- -- -- -- --

Here, you can see a device at 0x49 and 0x70. I know I have a temperature sensor at 0x49, so the LED matrix must be at 0x70.

Find the code in LED matrix display (matrixLEDi2c.py) and run it by using the following command:

bone$ pip install smbus  # (Do this only once.)
bone$ ./matrixLEDi2c.py

LED matrix display (matrixLEDi2c.py)

Listing 37 LED matrix display (matrixLEDi2c.py)

#!/usr/bin/env python
# ////////////////////////////////////////
# //	i2cTemp.py
# //      Write an 8x8 Red/Green LED matrix.
# //	Wiring:	Attach to i2c as shown in text.
# //	Setup:	echo tmp101 0x49 > /sys/class/i2c-adapter/i2c-2/new_device
# //	See:	https://www.adafruit.com/product/902
# ////////////////////////////////////////
import smbus
import time

bus = smbus.SMBus(2)  # Use i2c bus 2       ①
matrix = 0x70         # Use address 0x70    ②
ms = 1;               # Delay between images in ms

# The first byte is GREEN, the second is RED.   ③
smile = [0x00, 0x3c, 0x00, 0x42, 0x28, 0x89, 0x04, 0x85,
    0x04, 0x85, 0x28, 0x89, 0x00, 0x42, 0x00, 0x3c
]
frown = [0x3c, 0x00, 0x42, 0x00, 0x85, 0x20, 0x89, 0x00,
    0x89, 0x00, 0x85, 0x20, 0x42, 0x00, 0x3c, 0x00
]
neutral = [0x3c, 0x3c, 0x42, 0x42, 0xa9, 0xa9, 0x89, 0x89,
    0x89, 0x89, 0xa9, 0xa9, 0x42, 0x42, 0x3c, 0x3c
]

bus.write_byte_data(matrix, 0x21, 0)   # Start oscillator (p10) ④
bus.write_byte_data(matrix, 0x81, 0)   # Disp on, blink off (p11)
bus.write_byte_data(matrix, 0xe7, 0)   # Full brightness (page 15)

bus.write_i2c_block_data(matrix, 0, frown)      # ⑤
for fade in range(0xef, 0xe0, -1):              # ⑥
    bus.write_byte_data(matrix, fade, 0)
    time.sleep(ms/10)

bus.write_i2c_block_data(matrix, 0, neutral)
for fade in range(0xe0, 0xef, 1):
    bus.write_byte_data(matrix, fade, 0)
    time.sleep(ms/10)

bus.write_i2c_block_data(matrix, 0, smile)

matrixLEDi2c.py

① This line states which bus to use. The last digit gives the I²C bus number.

② This specifies the address of the LED matrix, 0x70 in our case.

③ This indicates which LEDs to turn on. The first byte is for the first column of green LEDs. In this case, all are turned off. The next byte is for the first column of red LEDs. The hex 0x3c number is 0b00111100 in binary. This means the first two red LEDs are off, the next four are on, and the last two are off. The next byte (0x00) says the second column of green LEDs are all off, the fourth byte (0x42 = 0b01000010) says just two red LEDs are on, and so on. Declarations define four different patterns to display on the LED matrix, the last being all turned off.

④ Send three commands to the matrix to get it ready to display.

⑤ Now, we are ready to display the various patterns. After each pattern is displayed, we sleep a certain amount of time so that the pattern can be seen.

⑥ Finally, send commands to the LED matrix to set the brightness. This makes the display fade out and back in again.

Driving a 5 V Device

Problem

You have a 5 V device to drive, and the Bone has 3.3 V outputs.

Solution

If you are lucky, you might be able to drive a 5 V device from the Bone’s 3.3 V output. Try it and see if it works. If not, you need a level translator.

What you will need for this recipe:

• A PCA9306 level translator

• A 5 V power supply (if the Bone’s 5 V power supply isn’t enough)

The PCA9306 translates signals at 3.3 V to 5 V in both directions. It’s meant to work with I²C devices that have a pull-up resistor, but it can work with anything needing translation.

Wiring a PCA9306 level translator to an LED matrix shows how to wire a PCA9306 to an LED matrix. The left is the 3.3 V side and the right is the 5 V side. Notice that we are using the Bone’s built-in 5 V power supply.

Fig. 433 Wiring a PCA9306 level translator to an LED matrix

Note

If your device needs more current than the Bone’s 5 V power supply provides, you can wire in an external power supply.

Writing to a NeoPixel LED String Using the PRUs

Problem

You have an Adafruit NeoPixel LED string or Adafruit NeoPixel LED matrix and want to light it up.

Solution

The PRU Cookbook has a nice discussion (WS2812 (NeoPixel) driver) on driving NeoPixels.

Fig. 434 Wiring an Adafruit NeoPixel LED matrix to P9_29

Writing to a NeoPixel LED String Using LEDscape

Making Your Bone Speak

Problem

Your Bone wants to talk.

Solution

Just install the flite text-to-speech program:

bone$ sudo apt install flite

Then add the code from A program that talks (speak.js) in a file called speak.js and run.

Listing 38 A program that talks (speak.js)

#!/usr/bin/env node

var exec = require('child_process').exec;

function speakForSelf(phrase) {
{
	exec('flite -t "' + phrase + '"', function (error, stdout, stderr) {
        console.log(stdout);
        if(error) { 
            console.log('error: ' + error); 
        }
        if(stderr) {
            console.log('stderr: ' + stderr); 
        }
        });
}

speakForSelf("Hello, My name is Borris. " +
    "I am a BeagleBone Black, " +
    "a true open hardware, " +
    "community-supported embedded computer for developers and hobbyists. " +
    "I am powered by a 1 Giga Hertz Sitara™ ARM® Cortex-A8 processor. " +
    "I boot Linux in under 10 seconds. " +
    "You can get started on development in " +
    "less than 5 minutes with just a single USB cable." +
    "Bark, bark!"
    );

speak.js

See Playing and Recording Audio to see how to use a USB audio dongle and set your default audio out.